Almost everyone may have their private opinion in relation to Tools You Need to Install a New Bathtub .
Installing a bath tub isn't exactly rocket science, but it does call for solid plumbing, woodworking, and sometimes, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably tough job. If the old tub is conveniently accessible, the project can move quickly; if you have to open up a wall surface to remove the old bathtub as well as place the new bath tub, the job is much harder. In either situation, the task is within a residence handyman's abilities, although you will require a helper to move out the old tub and also set in the brand-new one. Ensure you have actually certified yourself for the task as well as fit trying it. Rather than working with a contractor to take over a halfway-completed task, it is much better to consider employing one before you begin. Chances are you might need a specialist plumber to make tube connections.
This post will aid you set up a brand-new tub in your washroom if you have actually currently bought a brand-new bathtub as well as do not require to alter the setup of your previous water pipes.
Your tools and product list should consist of the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain pipes any water remaining in the system. The procedure of removing the existing faucets can be quite problematic because of the restricted gain access to that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will come from the pipelines. As soon as the supply pipelines have been removed, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before proceeding to fit the brand-new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin ensuring that the washers are in area between the faucet and also the sink. Protect the tap in position with the maker offered backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap connectors. The former kind ought to be connected to the tap finishes first, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Bathtub
Utilizing the two wood boards under its feet, position the bath tub in the called for setting. The wooden boards are helpful in uniformly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next goal is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the tub until the level reads level.
To install taps, fit the bottom of the outermost flexible tap connector to the ideal supply pipe by making a compression join; then do the very same for the other tap.
Turn on the water as well as inspect all joints and new pipework for leakages and tighten them if essential. Fill up the bathtub as well as also check the overflow electrical outlet and also the regular outlet for leaks.
Finally, take care of the bath paneling as explained in the producer's instruction manual. Tiling and also securing around the bathtub should wait till the tub has actually been made use of at the very least when as this will resolve it into its last setting.
Getting ready for the Installation
To start with, the supporting structure supplied with the bath should be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is essential to see to it that if the faucet features a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps device to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final setting.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split an inflexible seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, causing issues with dampness and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealants to blend in your components as well as installations. They are marketed in tubes and cartridges, as well as can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the bath tub with water prior to securing, to enable the motion experienced when the tub remains in use. The sealer can crack relatively early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily available on the market. It is suggested to fit the floor tiles making use of water-resistant or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed our part about Tools You Need to Install a New Bathtub . Thanks a lot for finding the time to browse our blog post. Are you aware of another person who is serious about the topic? Be sure share it. Many thanks for your time. Come back soon.
Overflow resolution available.